Stainless steel fasteners kit for VHB carb models without sump extension.This kit contains nuts, bolts and washers for the following: rocker covers, timing cover, gearbox bell housing, alternator cover, gearbox rear cover, neutral switch, drive box to swingarm, starter motor, head studs, exhaust flanges, inlet manifolds and sump. Just what you need to brighten up your Guzzi and ensure nuts and bolts don't seize on your bike

This engine bolt kit contains appropriate M6, M8, M10 socket cap and hex head bolts, nuts and washers. 145 pieces. To ensure you can easily release these fasteners in years to come we recommend wiping each fastener with copper grease (OIA11070). You may also require a replacement front engine bolt kit in stainless (SSA14450) or distributor screws (SSA05025 and SSA04008)

 More than 5 in stock

Pair of polished aluminium exhaust flanges. These will work with any Guzzi downpipes but work particularly well with Mistral downpipes which don't require exhaust collets

See ENA90718 for exhaust gaskets

 1 in stock

Regulator rectifier for Saprisa charging systems

Male spade connectors on regulator, may be supplied with 7 connectors - see the diagram on our technical documents page for help installing this part. The standard black block connector is not compatible with the updated 7 pin reg/rec, you will instead need to fit female spade connectors to your wires.

 This part is due back in stock soon, call 01484 841395 to reserve yours

28703800-z 28703800 GU28703800 28 70 38 00
 2870 3800 2870.3800 28.70.38.00

Ignition pickup and tacho sensor

Connector plug has two male spades. Also known as phase sensor. Used on models with the large Marelli P8 ECU. No longer available from Guzzi. Note 90° angle where cable exits sensor. See ENA90141 for O ring used to fit this part

 1 in stock

 29721660 GU29721660 29 72 16 60
 2972 1660 2972.1660 29.72.16.60

60° speedo drive for rear of speedo

 This part is available by special order, request a quote

 23768310 GU23768310 23 76 83 10
 2376 8310 2376.8310 23.76.83.10

Universal rack for mounting H & B top cases to luggage racks which don't have the H & B fitting. Includes grab rail, finished in black.

Because this is a universal rack you may need to do some additional drilling and obtain extra fasteners depending upon which type of luggage rack you are fitting this to

 This part is available by special order, request a quote

Polished aluminium alternator cover

For big twins with Bosch charging systems only. Not deep enough for later bikes with Ducati or Saprisa. See ACA18650 for deeper version.

 This part is available by special order, request a quote

18001650-z 18001650 GU18001650 18 00 16 50
 1800 1650 1800.1650 18.00.16.50

Front main bearing flange 0.2mm oversize

 This part is available by special order, request a quote

14011901-z 14011901 GU14011901 14 01 19 01
 1401 1901 1401.1901 14.01.19.01

Front main bearing flange 0.4mm oversize

 This part is available by special order, request a quote

14011902-z 14011902 GU14011902 14 01 19 02
 1401 1902 1401.1902 14.01.19.02

Front main bearing flange 0.6mm oversize

 This part is available by special order, request a quote

14011903-z 14011903 GU14011903 14 01 19 03
 1401 1903 1401.1903 14.01.19.03